Search

Home>>Industrial cameras>>Hitachi>>3CCD>>3CCD standard

Monochrome analog - Monochrome progressive scan - Color - 3 CCD color

3 CCD color - Progr.scan 3 CCD

All cameras are supplied without lens, unless otherwise indicated

For these cameras we recommend the use of lenses for 3CCD

HV-D20P
C mount lens. Newly developed LSI chip for a compact and low consumption power. High picture quality with high resolution (800 TV lines) and sensitivity. High S/N ratio of 62 dB. Compact and low consumption camera. New digital noise reduction system. 6 color independent masking: user can adjust hue and saturation of the three primary color (R,G, B) and complementar color (Mg, Ye, Cy) independently. Auto shading compensation (ASC) with three modes of shading: can automatically compensate for color shading errors caused by interaction between the lens and prism assembly in C-mount optical systems. Intelligent Auto Level Control (ALC). Unattended operation is possible with the selection  of the auto mode from the main menu. The built-in microprocessor controls the gain (AGC) function, the suto electronic shutter (AES) and auto iris function so the proper video level is maintained over a wide range of light levels. RS-232C interface.
Color system	PAL
Optical system	1/2", f1.6
Imaging system	RGB, 3 CCD
Total pixels	795 (H) x 596 (V)
Effective pixels	752 (H) x 582 (V)
Sensing area	6.35(H) x 4.78 (V) mm
Scanning system	2:1 interlace
Sync system	internal/external (VBS, BBS or Hd/Vd)
Horizontal resolution	800 TV lines (Y at center) (Y out and DTL off)
S/N ratio	62 dB (DNR on), 59 dB (DNR off) (Y out, gamma=1, DTL=Off, gain= 0 dB)
Standard sensitivity	2000 lux, f 11
Minimum illumination	0.4 lux (50IRE, f1.6, gain+24dB, digital gain +12dB)
Vertical contour correction	2H
Lens mount	C mount
Gain	AGC (0 to +24 dB) or GAIN (0 to +24dB, step 1dB or step 3dB on remote menu control)
Electronic shutter	1.Preset:  1/60, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000, 1/40000, 1/100000 sec 2. Lockscan: 1/50.31  to 1/2024 sec (step 1H) to 1/10000 sec (step approx 10% video level) 3.AES: from OFF to 1/100000 sec 4. Integration: 1/25 to approx 8 sec (1 frame steps) * external image memory needed for continuous image
Genlock input	VBS: 1 Vp-p +- 3dB  or black burst, 75Ω Hd/Vd 2 to 5Vp-p, negative (MULTI connector)
External trigger input	low 0 Vdc, high 2 to 4Vdc (MULTI connector)
Serial data input	1.5Vp-p/HIGH (when connected to RC-Z3, JU-C20, JU-Z2), RS232C level (when connected to PC) (remote connector)
Composite video output	VBS: 1 Vp-p, 75 ohm BNC (BNC, MULTI connector)
Y/C output	Y: 1 Vp-p, 75 ohm C: 0.3Vp-p (burst), 75 ohm (MULTI connector)
Component output	Y: 1 Vp-p, 75 ohm R-Y: 0.7Vp-p, 75 ohm B-Y: 0.7Vp-p, 75 ohm (MULTI connector)
RGB output	R: 0.7Vp-p. 75 ohm G: 0.7Vp-p. 75 ohm B: 0.7Vp-p. 75 ohm (MULTI connector)
Sync outputs	Hd: 2Vp-p, 75 ohm Vd: 2Vp-p, 75 ohm Sync: 2Vp-p, 75 ohm (MULTI connector)
Serial data output	1.5Vp-p/LOW (when connected to RC-Z3, JU-C20, JU-Z2), RS232C level (when connected to PC) (remote connector, MULTI connector)
Lens iris control output	1.5V (closed) to 5.5V (open) o 2.5V (closed) a 7.5V (open) selectable
The lens must have  a protrusion (T) from the flange face less than 3.9mm to be used with these cameras
Pins configuration	pins configuration
Operating temperature	-10C° to 45°C
Storage temperature	-20°C to + 60°C
Power supply	12Vdc rated (stable operation at 10.5 to 15Vdc)
Power consumption	@5.0W
Dimensions (W x H x D)	65 x 65 x 130mm  dimensional drawing
Weight	@450g not including lens

For these cameras we recommend the use of lenses for 3CCD

HV-D15AS   discontinued
High quality digital camera . 3rd generation 14 bit DSP for signal processing. Three 1/2" CCD sensors each with  470 K pixel. High resolution (850 lines) and high sensitivity (minimum illumination: 0.3 lux). High signal/noise ratio (63dB). Dynamic noise reduction (DNR). SDI (serial digital interface) video output compliant with SMPTE 259M standard. 12 bit A/D converter. Auto shading compensation. External trigger functions. RS-232C control.
Color system	PAL
Optical system	1/2", f1.4 prism
Imaging system	RGB, 3 CCD
Total pixels	795 (H) x 596 (V)
Effective pixels	752 (H) x 582 (V)
Effective image area	6.47(H) x 4.83 (V) mm
Scanning frequency	15.624 KHz(H), 50 Hz (V)
Sync system	internal/external (VBS, BBS or Hd/Vd auto selection)
Horizontal resolution	850 TV lines (luminance signal center) (Y out, DTL off)
S/N ratio	63 dB (DNR on), 60 dB (DNR off) (Y out, γ=1, DTL=off, gain 0 dB)
Standard sensitivity	2000 lux, f 11
Minimum illumination	0.3 lux (50 IRE, F1.4, gain +24dB, digital gain +12 dB)
Gamma	0.45 to 1 (on/off)
Geometric distortion	0% full screen (not including lens characteristics)
Registration	0,05% full screen (not including lens characteristics)
Vertical contour correction	2H
Lens mount	bayonet mount (flangeback 35.74 mm in air)
Sensitivity selection	AGC (0-+24dB), or GAIN (0 to +24 dB with 1dB steps or  3 dB steps on remote control menu)
Detail control	DTL level and frequency
Scene files	4 files
Digital gain	+6 dB, +12 dB sensitivity improvement by digital signal processing
Electronic shutter speeds	1.Preset values:  1/60, 1/250, 1/500, 1/1000, 1/2000, 1/4000,  1/10000, 1/20000, 1/40000, 1/100000 sec 2. Lockscan: 1/50.31  to 1/2024 (step 1H) to 1/100000 sec (step approx 10% video level) 3.AES: OFF to 1/100000 sec (step 10 F)
Color bar	FULL
Genlock input	VBS: 1 Vp-p ± 3 dB or black burst (Sync 0.3V+-0.1V), 75 ohm/high (BNC)
External trigger input	low 0 Vdc, high 2 to 5 Vdc
Serial data (remote connector)	1.5Vp-p/HIGH, RS-232C level
Component video output	VBS: 1 Vp-p, 75 ohm BNC
SDI output	SMPTE 259M
Output (remote connector)	1.5Vp-p/low (when connected to RC-Z3, JU-C2, JU-Z2) RS-232C level(when connected to PC)
Lens iris control output	IRIS CONT: 1.5V (close) to 5.5V (open) or 2.5V (close) to 7.5V (open)
Lens control output (segnale d'uscita)	ZOOM: 0 Vdc (wide)~5Vdc (tele)/1KΩ FUOCO: 0 Vdc (near)~5Vdc (far)/1KΩ PAN: 0 Vdc (left)~5Vdc (right)/1KΩ TILT: 0 Vdc (up)~5Vdc (down)/1KΩ
Connectors
Operating temperature	-10C° to 45°C
Storage temperature	-20°C to + 60°C
Power supply	12Vdc rated (10.5 to 15Vdc)
Power consumption	@8.5W
Dimensions (W x H x D)	80 x 85 x 134mm dimensional drawing
Weight	@900g
Accessories	RC-Z3: control unit JU-Z2: junction unit JU-C20: RS-232C converter level

For these cameras we recommend the use of lenses for 3CCD

HV-D30P
High performance digital camera. Single 3 million gate ultra-LSI (large scale integration) processing chip. 12 bit analog/digital converter and 14 bit accelerated DSP. Compact cube dimensions. High resolution (800 lines) and high sensitivity(minimum illumination: 1.2 lux). High signal/noise ratio(64dB, 62 dB PAL) obtained with dynamic noise reduction. Two modes of Auto Shading Compensation (ASC); this function can automatically compensate for colour shading errors caused by interaction between the lens and prism assembly in C-mount optical systems. A six-vector colour corrector allows independent adjustment of hue and saturation. Optimum for microscope and other applications where colour fidelity is important. Two colours can be selected and the detail of each adjusted independently. Intelligent auto level control (ALC). External trigger; a scena can be captured at a desired timing and exposure time. Adjustable flange back. Allows the camera optical focus to be optimized. Four scene files are provided for setup, storage and recall of all camera functions. Dynamic chroma compensation. Flare compensation can be adjusted to compensate for colour changes in dark areas when using a zoom lens. Normal (positive) or negative picture polarity selectable. Full range of video outputs. The camera can be synchronized using the genlock input or external Hd and Vd signals. An RS-232C port allows complete control, setup, and operation of all camera functions.
Colour system	NTSC/PAL
Prism	1/3", f2.2
Lens mount	C
CCD	RGB, 3 CCD interline transfer
Total pixels	NTSC: 811(H) x 508(V) PAL: 795 (H) x 596 (V)
Effective pixels	NTSC: 768(H) X 494(V) PAL:  752 (H) x 582 (V)
Effective image area	NTSC: 4.88(H) x 3.66(V) mm PAL:  4.89(H) x 3.64 (V) mm
Horizontal resolution	800 lines TV (Y signal center, DTL off))
S/N ratio	NTSC: 64 dB (DNR On) PAL: 62 dB (DNR On)
Standard sensitivity	2000 lux, f 8.0
Sensitivity setting	AGC (from 0 to +24dB) manual (from  0 to +24 dB, 1dB step) and digital gain(approx +12 dB)
Minimum sensitivity	1.2 lux (with f2.2 e + 24 dB, digital gain on)
Electronic shutter	4 mode
Preset mode	1/100 sec (PAL 1/60 sec) to 1/100.000 sec, 10 steps
Lock scan mode	NTSC 1/60.38 sec to 1/100.000 sec PAL 1/50.38 sec to 1/100.000 sec
Auto electronic shutter         (AES)	from OFF to 1/100.000
Long term integration	field/frame integration selectable NTSC (1/30 to 8 sec) PAL (1/25 sec to 8 sec) 1 frame step external image memory needed for continuous image
External trigger	field/frame readout selectable one pulse trigger input
White balance mode	preset: 3200K°/5600K° selection memory: auto white balance auto: real time auto white balance
Scene files	4 files
Color bars	NTSC: SMPTE,  PAL: FULL
Genlock input	VBS: 1 Vp-p ± 3dB, or black burst,  75 Ω Hd/Vd 2 at 5 Vp-p, negative
External trigger input	Low: 0Vdc, High: from 2 to 5 Vdc
Serial data input	1.5Vp-p/High (when connected to RC-Z3) RS-232C level (when connected to PC)
Composite video output	VBS: 1 Vp-p, 75 Ω ohm
RGB output	0.7 Vp-p, 75 Ω ohm
Component output	Y: VS 1.0 Vp-p 75 Ω R-Y: 0.7  Vp-p 75 Ω B-Y: 0.7 Vp-p 75 Ω
Y/C output	Y: 1.0  Vp-p, 75 Ω ohm C: NTSC BURST:  0.28 Vp-p 75 Ω,   PAL BURST: 0.3 Vp-p 75 Ω
Sync output	Hd: 2 Vp-p, 75 Ω Vd: 2 Vp-p, 75 Ω
Serial data output	1.5Vp-p/LOW (when connected to RC-Z3) RS-232C level (when connected to PC)
Pins configuration	pins configuration
Operating temperature	-10C° to + 45°C
Storage temperature	-20°C to + 60°C
Vibration	2.5G The following vibration is added in each of up-down every direction for 30 minutes. frequency: 10-30Hz with a amplitude of 1.2mm frequency: 25Hz with a amplitude of 2mm
Shock	40G When it was made to fall on the wood engraving freely from the bottom part of the camera. Packing drop from 80cm heigh, freedom drop. (JIS standard Z 0200 Level I). At this test the camera is stored in the product packing box.
Power supply	12Vdc rated (stable operation at 10.5 to 15Vdc)
Consumption	@4.0W
Dimensions (W x H x D)	65 x 65 x 80mm dimensional drawing
Weight	@400g
Included accessories	power plug operation manual
Optional accessories	RC-Z3: camera control box JU-Z2: junction box

For these cameras we recommend the use of lenses for 3CCD

HV-D27/HV-D37
High quality Single chip VLSI for signal processing. High resolution (HV-D27: 800 lines, HV-37: 750 lines) Micro-lenses for High S/N ratio (60 dB). Digital noise reduction system. Selectable ultra gain (32 dB). 3 modes of white balance: auto-tracking, memory and preset at 3200°K. Hue and saturation correction for each of 3 primary colours and 3 complementary colours Dyna chroma and chroma gain circuits. Contrast and auto knee circuits. Auto shading and detail level correction Three application files for user selected setup information storage. Five preset patterns and 2 freely settable user memory for ALC (automatic lvel control) in conjuction with AGC(automatic gain control) and AES (automatic electronic shutter). 4 shutter operation modes Multiple output encoder for different output signals (RGB, Y/R-Y/B-Y, Y/C, video composite with Gen-lock. On-screen-display menu. Character generator with selectable position. RS-232C interface. Intelligent Auto Level Control (ALC) NTSC system available 3m cable between camera head and CCU supplied
	HV-D27	HV-D37
Colour system	PAL
Prism optics	1/2", f1.6	1/3", f2.2
Imagers	1/2" interline transfer CCD (with micro lenses)	1/3" interline transfer CCD (with micro lenses)
Effective pixels	752 (H) x 582 (V)
Sensing area	6.47(H) x 4.83 (V) mm
Encoder system	R-Y/B-Y
Sync system	internal/gen-lock
Horizontal resolution	800 TV lines (Y at center)	750 lines (Y at center)
S/N ratio	60dB	58 dB
Standard sensitivity	2000 lux, f 8.0
Minimum illumination	1.5 lux (50 IRE, f1.6, gain+20dB, Ultra gain=ON)	2.8 lux (50 IRE, f2.2, gain+20dB, Ultra gain=ON)
Gamma	0.35 to 1 (on/off)
Picture distortion	Total: 0% (not including lens characteristics)
Vertical contour correction	2H
Lens mount	C mount
Gain	AGC (0-+20dB), NORM/HIGH/MAX, ULTRA GAIN
Scene files	3
Electronic shutter	1.Preset values:  1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000,  1/10000 sec 2. Lock scan mode: 1/50.31 to 1/253.8 3. Auto electronic shutter: from OFF to 1/1000 4. Long term integration: from 1/25 to 8 sec (PAL)* * A video memory is needed for successive videos.
Colour bars	FULL
Gen-lock input signal	VBS: 1 Vp-p +-3dB, 75 ohm
Serial data output (input signal)	1.5Vp-p/HIGH,  RS-232C level
Composite video output	VBS: 1 Vp-p, 75 ohm BNC, D-sub connectors
Y/C output	Y: 1 Vp-p, 75 ohm C: 0.3Vp-p, 75 ohm (PAL) D-sub, Y/C connectors
Component output	Y: 1 Vp-p, 75 ohm R-Y: 0.7 Vp-p, 75 ohm B-Y: 0.7 Vp-p, 75 ohm D-sub connector
RGB output	R: 0.7Vp-p. 75 ohm G: 0.7Vp-p. 75 ohm B: 0.7Vp-p. 75 ohm D-sub connector
Sync output	Hd: 2Vp-p, 75 ohm Vd: 2Vp-p, 75 ohm Sync: 2Vp-p, 75 ohm D-sub connector
Serial data output (output signal)	1.5Vp-p/LOW,  RS-232C level
Operating temperature	0C° to 45°C
Storage temperature	-20°C to 60°C
Power supply	Rated 12Vdc (operable on 10.5 to 17Vdc, no ripple noise)
Power consumption	@10
Dimensions (W x H x D)	Head: 38.5 x 56 x 41.5 mm CCU: 150 x 45 x 170 mm dimensional drawing
Weight	Head:@ 90g (excluding lens and cable)

 

Reference technical notes
Introduction to CCD cameras

Cliccate sulle  parole evidenziate in giallo per vedere collegamenti a figure o ad altre pagine.
Click on words highlighted in yellow to view links.

Cliccate sulle immagini miniaturizzate per vederle ingrandite.
Click on thumbnails to view enlarged images.

Rapitron s.r.l.
NEW ADDRESS/NUOVO INDIRIZZO
  Via S.Antonio Maria Zaccaria 4  -  20122 Milano ITALIA
      Tel.: +39 02 659.82.82   Fax: +39 02 65.45.25

P.IVA/VAT No:  IT 04498890153

Queste pagine sono disegnate e aggiornate da Rapitron s.r.l.
I marchi citati sono di proprietà dei rispettivi proprietari.
Le specifiche dei prodotti sono esposte così come dichiarate dai singoli fabbricanti e sono soggette a cambiamenti senza preavviso.
Sito ospitato da Range s.a.s.- Genova

These pages are designed and updated esclusively by Rapitron s.r.l.
All trademarks are property of the respective owners.
All products specifications are shown as declared by manufacturers and are  subject to change without prior notice.
This Web Site is hosted by Range s.a.s. - Genova

Copyright ©2011 Rapitron s.r.l.
Last modified 19-12-2011