Hitachi b/w megapixel

Discontinued products
Industrial video
Progressive scan black/white megapixel cameras

Reference technical notes

	Introduction to CCD cameras
	Progressive scan cameras

Search

All cameras are supplied without lens, unless otherwise indicated

KP-F100UV

The specifications of this product appear as a reference only, as it has been discontinued

	Very high resolution cameras (1.450.000 pixels).
	CCD sensitivity from 240 nm to 930 nm.
	Square pixels produces an image suitable for processing in reduced time.
	1/2" CCD suitable for use with a microscope and image processing systems.
	Multi step electronic shutter up to 1/50000.
	RS-232C control function (some functions can also be set from a PC).
	EIA-644 (LDVS) single channel 10 bit 20.2 MHz digital output and analog input.
	Frame on demand function (image capture at the desired timing by using an external trigger)

Image device

1/2" interline transfer CCD

Effective no. of pixels

1392(H) x 1040(V)

Pixel pitch

4.65m x 4.65m

Sensing area

6.47mm (H) x 4.84mm (V)

Scanning

progressive

Aspect ratio

4:3

Frame rate

7.5 fps (full pixel readout)
30 fps (quad mode)

Horizontal scanning frequency

7.98 Khz

Sync system

Internal/external (automaticaly switched)

Sync input

Hd/Vd: TTL negative,1Kohm;
frequency deviation: +-1%

Video output

Digital EIA-644 (LDVS) single channel 10 bit
20.2MHz/channel
Analog output for image checking.

Electronic shutter

1/50000, 1/10000, 1/4000, 1/2000, 1/1000, 1/250, 1/125, 1/60, 1/30, Off
(selectable by external switch ,factory default: OFF)

Frame on demand function

External switch setting off, fixed shutter, two trigger, and one trigger

Sensitivity

400 lux F4 3200K

Power supply

12Vdc +-1V

Power consumption

@300mA

Relative humidity and temperature

operating: -0C to 40C, 90% or less
storage: -10C to 50C, 70% or less

Lens mount

Shock resistance

294 m/sec² (vertical, horizontal, once each face)

Vibration resistance

29 m/sec² (10Hz to 55 Hz, 30 min each on XYZ)

Dimensions (W x H x D)

44mm x 44mm x 78mm
dimensional drawing

Weight

@180g

Accessories

tripod adaptor
6 pin remote plug
12 pin plug
D OUT connector (26 pins)
junction box
dummy glass (AR coated)
AC adaptor
camera cables (2m, 5m, 10m)

KP-F102

spectral response curve

	Very high resolution cameras (1.300.000/1.000.000 pixels).
	Square pixels produces an image suitable for processing in reduced time.
	2/3" CCD suitable for use with a microscope and image processing systems.
	Partial scan function (16H, 64H, 128H, 512H); allows a capture time
	RS-422A digital and analog output.of more than 12 frames per second. The capture time can be set from a PC.
	RS-232C control function (some functions can also be set from a PC).
	EIA-644 (LDVS) single channel 10 bit 20.2 MHz digital output.
	Frame on demand function (image capture at the desired timing by using an external trigger) The specifications of this product appear as a reference only, as it has been discontinued

Image device

2/3" interline transfer CCD

Total no.of pixels

1360(H) x 1034(V)

Effective no. of pixels

1300(H) x 1030(V)

Pixel pitch

6.7m x 6.7m

Sensing area

8.71mm (H) x 6.90mm (V)

Scanning

non interlace

Horizontal scanning frequency

12.528 Khz

Vertical scanning frequency

12Hz

Sync system

Internal/external (automaticaly switched)

Sync input

Hd/Vd: 5Vp-p negative,1Kohm;
frequency deviation: +-1%

Video output

Digital EIA-644 (LDVS) single channel 10 bit
20.2MHz/channel

Read out speed

12fps for full scan or higher frame rates with partial scanning
(16H, 64H, 128H, 256H, 512H)

Sensitivity

400 lux (f4, 3200 K)

Minimum illumination

1 lux f1.4 without IR cut filter
optical IR cut filter

Electronic shutter

1/10000, 1/4000, 1/2000, 1/1000, 1/250, 1/125, 1/60, 1/30, Off
(selectable by external switch ,factory default: OFF)
diagram of electronic shutter

Frame on demand function

1. Fixed shutter mode.
2. Two trigger mode

Remote control

Shutter
Frame-on-demand
Gain
Black level
Partial scan

Power supply

12Vcc +-1V

Power consumption

@400mA

Relative humidity and temperature

operating: -0C to 40C,
90% or less
storage: -10C to 50C, 70% or less

Lens mount

Shock resistance

30G (30 minutes for each XYZ directions)

Vibration resistance

3G (once for each surface of top, bottom, left and side panels)

Dimensions (W x H x D)

44mm x 44mm x 110mm
dimensional drawing

Weight

@230g

Accessories

lens
tripod adaptor
junction box
cables with connectors (2m, 5m, 10m) (connector diagram)
power supply unit

Applications

inspection, pattern recognition, high resolution image filling, license plate monitoring, X-ray image processing.

KP-F110

spectral response curve

	Very high resolution cameras (1.300.000/1.000.000 pixels).
	Square pixels produces an image suitable for processing in reduced time.
	2/3" CCD suitable for use with a microscope.
	RS-422A digital and analog output.
	Frame on demand function (image capture at the desired timing by using an external trigger) The specifications of this product appear as a reference only, as it has been discontinued

Image device

2/3" interline transfer CCD

Total no.of pixels

1030(H) x 1030(V)

Effective no. of pixels

1024(H) x 1024(V)

Pixel pitch

6.7m x 6.7m

Sensing area

6.86mm (H) x 6.86mm (V)

Scanning

non interlace

Horizontal scanning frequency

33.75Khz

Vertical scanning frequency

30Hz

Sync system

Internal/external (automaticaly switched)

Sync input

Hd/Vd: L:0-0.4Vcc negative;
frequency deviation: +-0.005%

Video output

Digital output: RS-422A
Datas: Dual channel 10 bit
24.3MHz/channel

Analog output: 1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p Sync 0.3Vp-p negative

pins configuration

Sensitivity

400 lux (f4, 3200 K)

Minimum illumination

50 lux f1.4 without IR cut filter

S/N ratio

50 dB (analog output)
(sync system and shutter speed: 1/30)

Electronic shutter

1/10000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/120, 1/30
(selectable by external switch ,factory default: 1/30)
diagram of electronic shutter settings

Gamma

1.0 (analog output only)

Frame on demand function

Externally selectable to ON/OFF. External trigger signal needed. Fixed shutter mode. One trigger mode and two trigger modes selectable. Factory default:OFF

Power supply

12Vcc +-1V

Power consumption

@900mA (Load resistance at digital output side: 100ohm)

Relative humidity and temperature

operating: -0C to 40C,
90% or less
storage: -10C to 50C, 70% or less
when using for extended period of time be sure to use camera at 30C or less

Lens mount

Shock resistance

3G (30 minutes for each XYZ directions)

Vibration resistance

30G (once for each surface of top, bottom, left and side panels)

Dimensions (W x H x D)

60mm x 75mm x 190mm
dimensional drawing

Weight

700g

Applications: Image instrumentation/inspection, pattern recognition, license plate monitoring, scientific applications, X-ray image processing.

KP-F200

The specifications of this product appear as a reference only, as it has been discontinued

Small design progressive scan 1/1.8" camera.

Frame rate 24fps (up to 190fps with partial scan).

High resolution with 2.01 million pixels.

Frame on demand

	Fixed shutter mode
	Two trigger mode
	One trigger mode

Partial scan.

Hd/Vd sync.

8 step electronic shutter.

RS-232C control.

Camera Link version available: KP-F200CL

Imaging device

CCD 1/1.8" with progressive scan

Effective pixels

1628 (H) x 1236 (V)

Pixel pitch

4.4μm(H) x 4.4μ (V) (square lattice)

Imaging area

7.16mm(H) x 5.94mm(V)

Scanning system

progressive

Aspect ratio

4:3

Frame rate

24fps (full pixel readout)

Scanning rate

horizontal: 30 KHz
vertical: 24 Hz

Synchronization

internal/externa (Hd/Vd)

Lens mount

C mount
(flange focal distance: 17.526mm)

Video output signals

RS-644

External sync input

Hd/Vd, LDVS level

Electronic shutter

1/50000, 1/10000, 1/2000, 1/1000, 1/250, 1/125, 1/60, 1/24 sec

Gamma

1.0

Frame on demand

external switch settings

Power supply

12Vdc 1V

Power consumption

approx 450 mA

Operating ambient

0 to +40C
less than 90%

Storage ambient

-10 to +50C
less than 70%

Vibration endurance

29.4 m/sec (10 to 200Hz, 30 minutes each on XYZ axes)

Shock endurance

294 m/sec (vertical, horizontal, once each face)

Dimensions (W x H x D)

58mm x 58mm x 48mm
dimensional drawing

Weight

approx 220g

Pin configuration

pin configuration

Connectors

RS-644 connector

Rear panel settings

modes selectors

Standard composition

camera, operating instructions

Optional accessories	SG1201/JMH0110	12V power supply with connector
	JMH0110	12 pin connector
	JMH0240	Digital connector
	JMH0092	Remote connector
	TA-F120	Tripod adapter
	C-201KSM	2m cable
	C-501KSM	5m cable
	C-102KSM	10m cable
		3m Camera Link cable
		3m Camera Link cable with mini connector