LogoRapitron

Sito in italianoDiscontinued products        
Industrial video
Progressive scan black/white cameras

Reference technical notes

bulletIntroduction to CCD cameras 
bulletProgressive scan cameras

Hitachi.gif (3813 byte)

KP-F2A/B

KP-F2 1/3" progressive scan near infrared camera

spectral response curve

bulletHigh resolution miniature camera with square pixels.
bulletHigh sensitivity in the near infrared spectrum.
bulletFuvertical resolution.
bulletKP-F2A:  1/30 sec full pixel frame output (1N).
bulletKP-F2B: 1/60 sec simultaneous output of separate signals from odd and even horizontal lines. The video signal can be obtained either from the rear panel multipin connector or from the 2 BNC video output.
bulletEight step shutter speed (from 1/60 to 1/8000 sec).
bulletInternal/external syncronization.
bulletFrame/field-on-demand function.

The specifications of this product appear as a reference only, as it has been discontinued

 KP-F2AKP-F2B
Imaging device

1/3" interline transfer CCD

Total pixels

680H) x 500(V)

Effective pixels

658(H) x 496(V)

Pixel size

7.4m x 7.4m

Sensing area

4.87mm (H) x 3.67mm (V)

Scanning

progressive (1/30 sec)

non interlace (1/60 sec)

Horizontal scanning frequency

15.734 Khz

Vertical scanning frequency

29.97 Hz

59.94 Hz

SyncronizationInternal/external Hd/Vd (automatic switching)
Internal sync525 horizontal lines262 horizontal lines
(1 output line)
External syncHd/Vd: 4to 6Vp-p negative,input impedance: 1Kohm,
 frequency accuracy +-1%
Video output1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p Sync 0.3Vp-p negative
Sensitivity30 lux (f4, 3200 K)
Minimum illumination0.3 lux f1.4 AGC=On, without IR cut filter
S/N ratio50 dB
Electronic shutter1/8000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/125, 1/60,OFF
(factory setting: OFF)
Gamma1.0 or correction (internal switch)
fixed gamma selectable for 2 video lines
(factory setting: 1)
AGCVideo out only settable for fixed gain or AGC
(external switch)
Factory setting: fixed
Frame/field on demand functionON/OFF (externally switchable)
ONE trigger and fixed shutter mode selectable by external switch
factory setting: OFF
Sensitivity selectionVideo Out 1: external switch settable for fixed gain or external control
Video Out 2: fixed gain
Both lines fine adjustable by internal controls
Factory setting: fixed
Lens mountC
Power supply12Vdc +-1V
Power consumption@200mA
Ambient temperature and relative humidityoperating: -0C to +40C, RH 90%
storage: -10C to +50C, RH 70% or less 
Vibration endurance test7G (10 to 60Hz, amplitude: 0.98mm constant; 60 to 200Hz, fixed acceleration, variable amplitude; 10 to 200Hz 1 minute sweep, 30 min each in 3 axes)
Shock endurance test

70G (once each: up, down, left, right)

Dimensions (W x H x D)44mm x 44mm x 87mm
dimensional drawing
Weight170g
Optional accessoriesSG1201/JMH011012V power supply with connector
JMH011012 pin connector
TA-F3Tripod adapter
C-201KSM2m cable
C-501KSM5m cable
C-102KSM10m cable

 

KP-F3

KPF3 1/3" b/w progressive scan camera

spectral response curve

bulletHigh sensitivity, high resolution miniature camera with square pixels.
bulletFull frame vertical resolution.
bulletIR cut filter.
bulletInterlace output at 1/60 sec; non interlace output at 1/30 sec.
bulletEight step shutter speed: from 1/100 to 1/8000 (KP-F3).
bulletInternal/external syncronization (Hd/Vd).
bulletFrame/field-on-demand function (one trigger mode/fixed shutter mode).
bulletVersion with same pin configuration as Sony XC-55 (KP-F3-S2).

The specifications of this product appear as a reference only, as it has been discontinued

Imaging device

1/3" interline transfer CCD

Scanninginterlace 2:1 (1/60 sec), non interlace (1/30 sec)
Signal formatEIA/progressive scan
Total pixels

699(H) x 503(V)

Effective pixels

647(H) x 485(V)

Pixel size

7.4m x 7.4m

Sensing area

4.79mm (H) x 3.59mm (V)

Horizontal scanning frequency

17.526 Khz

Vertical scanning frequency

59.94/29.97Hz

Resolution

500(H) x 485(V) TV lines

SyncronizationInternal/esternal(Automatic switching)
Int.sync.scanning systemInterlace: 1/60 sec
non interlace: 1/30 sec
External sync inputHd/Vd: 2 to 6Vp-p negative,input impedance 1Kohm, frequency deviation: +-1%
Video output1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p, Sync 0.3Vp-p, negative
Sensitivity400 lux (f5.6, 3200 K)
Minimum illumination0.2 lux f1.4 AGC=On, without IR cut filter
S/N ratio56 dB
Electronic shutter 1/8000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/100, OFF(normal exposure)
diagram of electronic shutter settings
Gamma1.0 or correction (by internal switches) 
Frame/field on demand functionSelectable ON/OFF by internal switches.
Selectable to ONE trigger mode or fixed shutter mode.
Set to OFF to factory.
diagram of electronic shutter settings for frame/field on demand function
Lens mountC
Power supply12Vdc +-1V
Power consumption@1.4W
Temperature and relative humidity Operating: -10C to +50C, 90% or less
Storage: -20C to 60C, 70% or less
Anti-vibration10G (10 to 60Hz, amplitude: 0.98mm constant; 60 to 200Hz,acceleration constant, amplitude variable; 10 to 200Hz one sweep each  XYZ, duration 30 min each)
Anti-shock70G (Once each top/bottom/left side/right side)
Dimensions (L x A x P)29mm x 29mm x 62mm
dimensional drawing
Weight100g
Rear panelKPF3 Rear panel
Optional accessoriesSG1201/JMH011012V power supply with connector
JMH011012 pin connector
TA-F3Tripod adapter
JU-F1Junction unit
C-201KSM2m cable
C-501KSM5m cable
C-102KSM10m cable

 

 

KP-F1A-S4

KPF1EK Progressive scan monochrome camera

spectral response curve

bulletHigh sensitivity, high resolution miniature camera with square pixels.
bulletFull frame vertical resolution.
bulletSimultaneous output of odd and even field signals at 1/50 sec in non-interlace (2N) and interlace (2I) mode.
bulletNon interlace output at 1/25 sec (1N).
bulletEight step shutter speed (from 1/120 to 1/10000).
bulletInternal/external syncronization.
bulletField-on-demand function.
bulletSpecial cleaned CCD.

The specifications of this product appear as a reference only, as it has been discontinued

Image device

1/2" interline transfer CCD

Total pixels

823(H) x 592(V)

Effective pixels

782(H) x 582(V)

Pixel size

8.3m x 8.3m

Sensing area

6.49mm (H) x 4.83mm (V)

Horizontal scanning frequency

15.625 Khz

Vertical scanning frequency

50Hz

TV resolution

580(H) x 575(V)

Sync systemInternal/external Hd/Vd (automatic switching)
External syncHd/Vd: 5Vp-p negative,1Kohm
Video output1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p Sync 0.3Vp-p negative
Sensitivity400 lux (f4, 3200 K)
Minimum illumination3 lux f1.4 AGC=On, without IR cut filter
S/N ratio60 dB
Electronic shutter1/10000, 1/4000, 1/2000, 1/1000, 1/500, 1/250, 1/125, 1/120
(low speed shutter available on request)
diagram of electronic shutter settings
Gamma1.0 or correction (built-in switch) 
Sensitivity switchingfixed gain, AGC or ext.control(only for VIDEO OUT 1)
Field on demand function4 modes available by built-in switches
Lens mountC
Power supply12Vdc +-1V
Power consumption@250mA
Temperature and relative humidity -10C to +50C,
 90% RH or less
Anti-vibration7G (10 to 60Hz, amplitude: 0.98mm constant; 60 to 200Hz, amplitude: variable, 7G constant)
Dimension (W x H x D)44mm x 44mm x 67mm
dimensional drawing 
Weight150g
Rear panelRear panel
Applications: Image processing.
Optional accessoriesSG1201/JMH011012V power supply with connector
JMH011012 pin connector
TA-M1Tripod adapter
JU-F1Junction unit
C-201KSM2m cable
C-501KSM5m cable
C-102KSM10m cable

 

KP-F3W

1/3" b/w progressive scan camera

spectral response curve
The specifications of this product appear as a reference only, as it has been discontinued

bulletHigh sensitivity, high resolution miniature camera with square pixels.
bulletFull frame vertical resolution.
bulletIR cut filter.
bulletDouble speed camera (KP-F3W).
bulletInterlace output at 1/120 sec; non interlace output at 1/60 sec.
bulletEight step shutter speed:  from 1/200 to 1/16000.
bulletInternal/external syncronization (Hd/Vd).
bulletFrame/field-on-demand function (one trigger mode/fixed shutter mode).
Imaging device

1/3" interline transfer CCD

Scanninginterlace 2:1 (1/60 sec), non interlace (1/30 sec)
Signal formatEIA/progressive scan
Total pixels

699(H) x 503(V)

Effective pixels

647(H) x 485(V)

Pixel size

7.4m x 7.4m

Sensing area

4.79mm (H) x 3.59mm (V)

Horizontal scanning frequency

17.526 Khz

Vertical scanning frequency

59.94/29.97Hz

Resolution

500(H) x 485(V) TV lines

SyncronizationInternal/esternal(Automatic switching)
Int.sync.scanning systeminterlace: 1/120 sec
non interlace: 1/60 sec
External sync inputHd/Vd: 2 to 6Vp-p negative,input impedance 1Kohm, frequency deviation: +-1%
Video output1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p, Sync 0.3Vp-p, negative
Sensitivity400 lux (f5.6, 3200 K)
Minimum illumination0.2 lux f1.4 AGC=On, without IR cut filter
S/N ratio56 dB
Electronic shutter 1/16000, 1/8000, 1/4000, 1/2000, 1/1000, 1/500, 1/200, OFF (normal exposure)
diagram of electronic shutter settings
Gamma1.0 or correction (by internal switches) 
Frame/field on demand functionSelectable ON/OFF by internal switches.
Selectable to ONE trigger mode or fixed shutter mode.
Set to OFF to factory.
diagram of electronic shutter settings for frame/field on demand function
Lens mountC
Power supply12Vdc +-1V
Power consumption@1.4W
Temperature and relative humidity Operating: -10C to +50C, 90% or less
Storage: -20C to 60C, 70% or less
Anti-vibration10G (10 to 60Hz, amplitude: 0.98mm constant; 60 to 200Hz,acceleration constant, amplitude variable; 10 to 200Hz one sweep each  XYZ, duration 30 min each)
Anti-shock70G (Once each top/bottom/left side/right side)
Dimensions (L x A x P)29mm x 29mm x 62mm
dimensional drawing
Weight100g
Optional accessoriestripod adaptor
12 pins plug
12 pins camera cable (2m, 5m, 10m)
junction box
power supply
Rear panelKPF3 Rear panel

 

KP-F100

KP-F100 Monochrome progressive scan 2/3" camera
spectral response curve
The specifications of this product appear as a reference only, as it has been discontinued

bulletVery high resolution cameras (1.300.000/1.000.000 pixels).
bulletSquare pixels produces an image suitable for processing in reduced time.
bullet2/3" CCD suitable for use with a microscope.
bulletRS-422A digital and analog output.
bulletFrame on demand function (image capture at the desired timing by using an external trigger)
Image device

2/3" interline transfer CCD

Total no.of pixels

1360(H) x 1034(V)

Effective no. of pixels

1300(H) x 1030(V)

Pixel pitch

6.7m x 6.7m

Sensing area

8.71mm (H) x 6.90mm (V)

Scanning

non interlace

Horizontal scanning frequency

12.528 Khz

Vertical scanning frequency

12Hz

Sync systemInternal/external (automaticaly switched)
Sync inputHd/Vd: 5Vp-p negative,1Kohm;
frequency deviation: +-1%
Video outputDigital output: RS-422A
Datas: Single channel 10 bit
20.2MHz/channel
Analog output: 1Vp-p video composite, 75 ohm,
Video: 0.7Vp-p   Sync 0.3Vp-p negative
Selectable by internal switch
 (Factory default: OFF) 
pins configuration
Sensitivity400 lux (f4, 3200 K)
Minimum illumination1 lux f1.4 without IR cut filter
S/N ratio50 dB (analog output)
Electronic shutter1/10000, 1/4000, 1/2000, 1/1000, 1/250, 1/125, 1/60, 1/30
(selectable by external switch ,factory default: OFF)
diagram of electronic shutter and read out speed settings
Gamma1.0 (analog output only) 
Frame on demand functionExternally selectable to ON/OFF. External trigger signal needed. Fixed shutter mode.Two trigger mode and  SYNC non reset modes selectable. Factory default: OFF
Power supply12Vcc +-1V
Power consumption@500mA
Relative humidity and temperatureoperating: -0C to 40C,
 90% or less
storage: -10C to 50C, 70% or less
when using for extended period of time be sure to use camera at 40C or less 
Lens mountC
Shock resistance3G (30 minutes for each XYZ directions)
Vibration resistance30G (once for each surface of top, bottom, left and side panels)
Dimensions (W x H x D)44mm x 44mm x 110mm
dimensional drawing
Weight200g
Applications: Image instrumentation/inspection, pattern recognition, license plate monitoring, scientific applications, X-ray image processing.

 

 

KP-F100A

KPF100A 2/3" b/w progressive scan with 1300 x 1030 pixels
The specifications of this product appear as a reference only, as it has been discontinued

bulletVery high resolution cameras (1.300.000 pixels).
bulletSquare pixels produces an image suitable for processing in reduced time.
bullet2/3" CCD suitable for use with a microscope and image processing systems.
bulletMulti step electronic shutter up to 1/50000.
bulletRS-232C control function (some functions can also be set from a PC).
bulletEIA-644 (LDVS) single channel 10 bit 20.2 MHz digital output.
bulletFrame on demand function (image capture at the desired timing by using an external trigger)
Image device

2/3" interline transfer CCD

Total no.of pixels

1360(H) x 1034(V)

Effective no. of pixels

1300(H) x 1030(V)

Pixel pitch

6.7m x 6.7m

Sensing area

8.71mm (H) x 6.90mm (V)

Scanning

progressive

Horizontal scanning frequency

12.528 Khz

Vertical scanning frequency

12Hz

Sync systemInternal/external (automaticaly switched)
Sync inputHd/Vd: TTL negative,1Kohm;
frequency deviation: +-1%
Video outputDigital  EIA-644 (LDVS) single channel 10 bit
20.2MHz/channel
Analog output for image checking.
Read out speed12fps for full scan
24 fps  (2V pixels simultaneous readout)
Electronic shutter1/50000, 1/10000, 1/4000, 1/2000, 1/1000, 1/250, 1/125, 1/60, 1/30, Off
(selectable by external switch ,factory default: OFF)
Frame on demand functionExternal switch setting off, fixed shutter, two trigger, and one trigger
Remote controlShutter
Frame-on-demand
Gain
Black level
Partial scan
Power supply12Vcc +-1V
Power consumption@290mA
Relative humidity and temperatureoperating: -0C to 40C,
 90% or less
storage: -10C to 50C, 70% or less
Lens mountC
Shock resistance294 m/sec2 (vertical, horizontal, once each face)
Vibration resistance29 m/sec2 (10Hz to 55 Hz, 30 min each on XYZ)
Dimensions (W x H x D)44mm x 44mm x 78mm
dimensional drawing
Weight@180g
Accessoriestripod adaptor
6 pin remote plug
12 pin plug
D OUT connector (26 pins)
junction box
dummy glass (AR coated)
AC adaptor
camera cables (2m, 5m, 10m)
 
HOME PAGE ENGLISH
COMPANY PROFILE
HOT NEWS
OFFERS
INFO
MAILING LIST
SEARCH
 
PRODUCTS RANGE
Security
Surveillance cameras
CCTV lenses
Digital Video Recorders
Monitors
IR and white light lamps
Video signal control devices
Pan & tilts
Housings
Machine vision
Industrial cameras
Machine vision lenses
Lighting for machine vision
Other products
Photographic and medical printers
DISCONTINUED PRODUCTS DATA BANK
 
TECHNICAL NOTES 
Optical calculator

Cliccate sulle  parole evidenziate in giallo per vedere collegamenti a figure o ad altre pagine.
Click on words highlighted in yellow to view links.

Cliccate sulle immagini miniaturizzate per vederle ingrandite.
Click on thumbnails to view enlarged images.

© Rapitron s.r.l.  -  1998-2012

NEW ADDRESS/NUOVO INDIRIZZO
Via S. Antonio Maria Zaccaria 4  -  20122 Milano ITALIA
Tel.: +39 02 659.82.82     Fax: +39 02 65.45.25

P.IVA/VAT No:  IT 04498890153

Queste pagine sono disegnate e aggiornate da Rapitron s.r.l.
I marchi citati sono di proprietà dei rispettivi proprietari.
Le specifiche dei prodotti sono esposte così come dichiarate dai singoli fabbricanti e sono soggette a cambiamenti senza preavviso.
Sito ospitato da Range s.a.s.- Genova

These pages are designed and updated esclusively by Rapitron s.r.l.
All trademarks are property of the respective owners.
All products specifications are shown as declared by manufacturers and are  subject to change without prior notice.
This Web Site is hosted by Range s.a.s. - Genova