Interlaced color

All cameras are supplied without lens, unless otherwise indicated
NTSC models available on request

	Low cost miniature camera.
	10 bit DSP for camera setup and configuration

	PAL and Y/C video output (STC-63CJ, STC-63CT only).
	Mirror function.
	Auto or lock to set white balance (STC-63CJ, STC-63CT only).
	High sensitivity, low light version (STC-HP63).

Camera configurations

STC-P63BJ

STC-P63BT

	Power jack
	BNC connector for video
	DC auto iris lens connector
	Autoiris level control

	Power terminal
	BNC connector for video
	DC auto iris lens connector
	Autoiris level control

STC-P63CJ

STC-P63CT

	Power jack
	BNC connector for video
	Y/C connector for Y/C output
	PC communication terminal (I2C)

	Power terminal
	BNC connector for video
	Y/C connector for Y/C output
	PC communication terminal (I2C)

	STC-P63BJ STC-HP63BJ	STC-P63BT STC-HP63BT	STC-P63CJ STC-HP63CJ	STC-P63CT STC-HP63CT
Imager	1/3" interline transfer CCD
Pixels	752 (H) x 582 (V)
Cell size	6.50μ x 6.25μ
Scanning	625 lines 50 Hz, 2:1 interlace
Horizontal frequency	15.625 Hz
Vertical frequency	50 Hz
Sync	internal
Signal processing	10 bit DSP (user programmable)
TV resolution	480 lines
S/N ratio	> 48 dB (AGC off)
Minimum illumination	STC-P63: 0.17 lux STC-HP63: 0.14 lux with f=1.2 (AGC On, 50 IRE)
Shutter	1/50 sec, electronic iris (DIP switches selectable) auto: 1/50-1/100000 sec
Video output	VBS		VBS, Y/C
Serial port	-		RS-232C
DSP	I2C (with USB adapter)
White balance	AWB		AWB, WB lock, PWB
Gain	ON
Gamma	0.45
Backlight compensation	ON/OFF (DIP switches selectable)
Aperture correction	ON
Pixel correction	ON
Flicker compensation	ON/OFF (DIP switches selectable)
Mirror	ON/OFF (DIP switches selectable)
Negative/Positive	selectable
Lens mount	CS (C with adapter)
Autoiris mount	DC autoiris		-
Power supply	10.5-14Vdc
Power consumption	150mA		180mA
Power connectors	jack	terminals	jack	terminals
Operating temperature	-10C� to 40C�
Dimension (W x H x D)	36mm x 36mm x 37.5mm dimensional drawing
Weight	65g

STC-625

	Miniature high resolution colour camera with 1/2" CCD.
	10 bit DSP for camera setup and configuration
	External synchronization (CC and CT models only).
	PAL and Y/C video output (selected models only)
	Auto or speed selectable shutter
	Full function controls (white balance, AGC/MGC, shutter)
	RS-232C controllable (C and CT models only).
	High sensitivity, low light version (STC-H625).

Camera configurations

STC-625A

STC-625CC

STC-625CT

Power jack

RCA connector for video output

Manual controls for:
color
brightness
sharpness

12 pin Hirose
power
Y/C out
Hd/Vd in

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

Power terminal

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

DC auto iris lens connector.

Auto iris level control

STC-625AS

STC-625BJ

STC-625BT

12 pin Hirose
power
Y/C out

BNC connector for video output

Manual controls for:
color
brightness
sharpness
gamma

	Power jack
	BNC connector for video
	DC auto iris lens connector

	Power terminal
	BNC connector for video output
	DC auto iris lens connector.
	Auto iris level control

Imager	CCD 1/2" interline transfer imager spectral response
Pixels	752 (H) x 582 (V)
Scanning	625 lines 50 Hz, interlace 2:1
Horizontal frequency	15.625 Hz
Vertical frequency	50 Hz
Syncronization	A, AS, BJ, BT: internal model CC: internal/external (Hd, Vd) model CT: internal/external (Vbs)
Signal processing	10 bit DSP (user programmable)
TV resolution	480 lines
S/N ratio	> 48 dB (AGC off)
Minimum illumination	STC-625: 0.72 lux STC-H635: 0.24 lux with f=1.2 (AGC on, 50 IRE)
Electronic shutter	Automatic: 1/50-1/10.000 Low speed: 2FLD - 16FLD (8 steps) High speed: 1/50-1/10.000 shutter speed settings
Video output	VBS=1Vp-p 75 ohm (PAL) Y/C (S-VHS) (AS, CC, CT models only) pin configuration
Serial port	RS-232C for remote control (CC and CT models only)
White balance	models BT, BJ, CC, CT: ATW/manual models A, AS:manual (rear panel volume control knob)
Gain	models BT, BJ, CC, CT:ON/OFF selectable , 0 to 12 dB range models A, AS: manual (rear panel volume control knob)
Gamma	models A, AS: 0.2, 0.45, 0.6, 1 models BT, BJ: 0.45 models CC, CT: 0.45, 1 (DSP adjustable)
Backlight compensation	activated with electronic shutter
Edge enhancement	(aperture gain), 4 setting switch selectable (A model only)
Negative/Positive	selectable
Lens mount	CS standard (C mount optional with adapter)
Output connectors	BNC & Y/C
Auto iris lenses	without amplifier (DC drive) on models BJ, BT, CT only
Power supply	10-12Vdc 250 mA
Operating temperature	from -10C� to 40C�
Dimensions (W x H x D)	51mm x 51mm x 55.5mm dimensional drawing
Weight	205g
Applications: pipe inspection, robotics, vision systems, microscopy, medical research, remote surveillance.

STC-635

	Miniature high resolution colour camera with 1/3" CCD.
	10 bit DSP for camera setup and configuration.
	External synchronization (CC and CT models only).
	PAL and Y/C video output (selected models only).
	Auto or speed selectable shutter.
	Full function controls (white balance, AGC/MGC, shutter).
	RS-232C controllable (C and CT models only).
	High sensitivity, low light version (STC-H635).

Camera configurations

STC-635A

STC-635CC

STC-635CT

Power jack

RCA connector for video output

Manual controls for:
color
brightness
sharpness

12 pin Hirose
power
Y/C out
Hd/Vd in

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

Power terminal

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

DC auto iris lens connector.

Auto iris level control

STC-635AS

STC-635BJ

STC-635BT

12 pin Hirose
power
Y/C out

BNC connector for video output

Manual controls for:
color
brightness
sharpness
gamma

	Power jack
	BNC connector for video
	DC auto iris lens connector

	Power terminal
	BNC connector for video output
	DC auto iris lens connector.
	Auto iris level control

Imager	CCD 1/3" interline transfer imager spectral response
Pixels	752 (H) x 582 (V)
Scanning	625 lines 50 Hz, interlace 2:1
Horizontal frequency	15.625 Hz
Vertical frequency	50 Hz
Syncronization	A, AS, BJ, BT: internal model CC: internal/external (Hd, Vd) model CT: internal/external (Vbs)
Signal processing	10 bit DSP (user programmable)
TV resolution	480 lines
S/N ratio	> 48 dB (AGC off)
Minimum illumination	STC-635: 0.64 lux STC-H635: 0.24 lux with f=1.2 (AGC on, 50 IRE)
Electronic shutter	Automatic: 1/50-1/10.000 Low speed: 2FLD - 16FLD (8 steps) High speed: 1/50-1/10.000 shutter speed settings
Video output	VBS=1Vp-p 75 ohm (PAL) Y/C (S-VHS) (AS, CC, CT models only) pin configuration
Serial port	RS-232C for remote control (CC and CT models only)
White balance	models BT, BJ, CC, CT: ATW/manual models A, AS:manual (rear panel volume control knob)
Gain	models BT, BJ, CC, CT:ON/OFF selectable , 0 to 12 dB range models A, AS: manual (rear panel volume control knob)
Gamma	models A, AS: 0.2, 0.45, 0.6, 1 models BT, BJ: 0.45 models CC, CT: 0.45, 1 (DSP adjustable)
Backlight compensation	activated with electronic shutter
Edge enhancement	(aperture gain), 4 setting switch selectable (A model only)
Negative/Positive	selectable
Lens mount	CS standard (C mount optional with adapter)
Output connectors	BNC & Y/C
Auto iris lenses	without amplifier (DC drive) on models BJ, BT, CT only
Power supply	10-12Vdc 250 mA
Operating temperature	from -10C� to 40C�
Dimensions (W x H x D)	51mm x 51mm x 55.5mm dimensional drawing
Weight	205g
Applications: pipe inspection, robotics, vision systems, microscopy, medical research, remote surveillance.

STC-645

	Miniature high resolution colour camera with 1/4".
	10 bit DSP for camera setup and configuration.
	External synchronization (CC and CT models only).
	PAL and Y/C video output (selected models only).
	Auto or speed selectable shutter.
	Full function controls (white balance, AGC/MGC, shutter).
	RS-232C controllable (C and CT models only).
	High sensitivity, low light version (STC-H645).

Camera configurations

STC-645A

STC-645CC

STC-645CT

Power jack

RCA connector for video output

Manual controls for:
color
brightness
sharpness

12 pin Hirose
power
Y/C out
Hd/Vd in

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

Power terminal

BNC connector for video output

Y/C connector for Y/C out

RS-232 mini-jack
DSP setup
camera control

DC auto iris lens connector.

Auto iris level control

STC-645AS

STC-645BJ

STC-645BT

12 pin Hirose
power
Y/C out

BNC connector for video output

Manual controls for:
color
brightness
sharpness
gamma

	Power jack
	BNC connector for video
	DC auto iris lens connector

	Power terminal
	BNC connector for video output
	DC auto iris lens connector.
	Auto iris level control

Imager	CCD 1/4" interline transfer imager spectral response
Pixels	752 (H) x 582 (V)
Scanning	625 lines 50 Hz, interlace 2:1
Horizontal frequency	15.625 Hz
Vertical frequency	50 Hz
Syncronization	A, AS, BJ, BT: internal model CC: internal/external (Hd, Vd) model CT: internal/external (Vbs)
Signal processing	10 bit DSP (user programmable)
TV resolution	480 lines
S/N ratio	> 48 dB (AGC off)
Minimum illumination	STC-645: 0.64 lux STC-H645: 0.5 lux with f=1.2 (AGC on, 50 IRE)
Electronic shutter	Automatic: 1/50-1/10.000 Low speed: 2FLD - 16FLD (8 steps) High speed: 1/50-1/10.000 shutter speed settings
Video output	VBS=1Vp-p 75 ohm (PAL) Y/C (S-VHS) (AS, CC, CT models only) pin configuration
Serial port	RS-232C for remote control (CC and CT models only)
White balance	models BT, BJ, CC, CT: ATW/manual models A, AS:manual (rear panel volume control knob)
Gain	models BT, BJ, CC, CT:ON/OFF selectable , 0 to 12 dB range models A, AS: manual (rear panel volume control knob)
Gamma	models A, AS: 0.2, 0.45, 0.6, 1 models BT, BJ: 0.45 models CC, CT: 0.45, 1 (DSP adjustable)
Backlight compensation	activated with electronic shutter
Edge enhancement	(aperture gain), 4 setting switch selectable (A model only)
Negative/Positive	selectable
Lens mount	CS standard (C mount optional with adapter)
Output connectors	BNC & Y/C
Auto iris lenses	without amplifier (DC drive) on models BJ, BT, CT only
Power supply	10-12Vdc 250 mA
Operating temperature	from -10C� to 40C�
Dimensions (W x H x D)	51mm x 51mm x 55.5mm dimensional drawing
Weight	205g
Applications: pipe inspection, robotics, vision systems, microscopy, medical research, remote surveillance.

Reference technical notes

Introduction to CCD cameras

Cliccate sulle parole evidenziate in giallo per vedere collegamenti a figure o ad altre pagine.
Click on words highlighted in yellow to view links.

Cliccate sulle immagini miniaturizzate per vederle ingrandite.
Click on thumbnails to view enlarged images.

Rapitron s.r.l.
NEW ADDRESS/NUOVO INDIRIZZO
Via S.Antonio Maria Zaccaria 4 - 20122 Milano ITALIA
Tel.: +39 02 659.82.82 Fax: +39 02 65.45.25

P.IVA/VAT No: IT 04498890153

Queste pagine sono disegnate e aggiornate da Rapitron s.r.l.
I marchi citati sono di propriet� dei rispettivi proprietari.
Le specifiche dei prodotti sono esposte cos� come dichiarate dai singoli fabbricanti e sono soggette a cambiamenti senza preavviso.
Sito ospitato da Range s.a.s.- Genova

These pages are designed and updated esclusively by Rapitron s.r.l.
All trademarks are property of the respective owners.
All products specifications are shown as declared by manufacturers and are subject to change without prior notice.
This Web Site is hosted by Range s.a.s. - Genova

Industrial video
Interlaced colour cameras

Copyright � 2011 Rapitron s.r.l.
Last modified 29-04-2011

Industrial videoInterlaced colour cameras

Copyright � 2011 Rapitron s.r.l.Last modified 29-04-2011

Industrial video
Interlaced colour cameras

Copyright � 2011 Rapitron s.r.l.
Last modified 29-04-2011