Search

Sentech cameras:

Custom - Black/white - Color - Line scan - Accessories

Other color cameras:

Interlaced board - Remote head board - USB board color
Interlaced color - Remote head - Camera Link -  USB - GigE - HD
Borescopes - Transit cameras - Zoom autofocus
Measurement software

All cameras are supplied without lens, unless otherwise indicated

STC-TC33USB-A/ASH
With software trigger		With software and hardware trigger

USB 2.0 interface. 1/3" progressive scan. VGA resolution. 0.45 o 1.0 gamma (variable software set). Electronic or fixed shutter. AGC On/Off selectable. Compact size. SDK Sentech available. Direct X and driver available. Soft trigger Extended low light capability via trigger software. Hard trigger versions available(STC-TC33USB-ASH) Four versions: with top connections (STC-TC33USB-AT). with back connections (STC-TC33USB-AS).
Download USB viewing software for 32x     HERE Download USB viewing software for 64x     HERE USB camera software user's manual  (V 8.0 pdf)
Configurations
AS	AT top view	AT rear view
ASH C mount	ASH CS mount	ASH rear view

		STC-TC33USB-AT STC-TC33USB-AS	STC-TC33USB-ASH
Resolution		VGA
Signal format		progressive scan
Image sensor		1/3" interline transfer CCD (ICX424AQ)
Effective pixels		659 (H) x 494 (V)
Total pixels		692 (H) x 504 (V)
Chip size		5.79 (H) x 4.89 (V) mm
Cell size		7.40 (H) x 7.40 (V) μm
Horizontal drive frequency		24.5454 MHz
Scanning methods		full scanning, 1/1 partial scanning, 1/2 partial scanning, 1/4 partial scanning, variable partial scanning
Horizontal drive frequency		24.5454 MHz
Maximum frame rate	full scan	59.94 fps
	1/2 partial scan	120.11 fps
	1/4 partial scan	240.22 fps
Resolution		640 (H) x 480 (V) at full scan 640 (H) x 224 (V) at 1/2 partial scan 640 (H) x 80 (V) at 1/4 partial scan
Minimum illumination		2.24 lux with f=1.2
Sync system		internal
Electronic shutter		auto (electronic iris)/manual (software selectable)
Gain		auto/manual (software selectable)
Gamma		manual (software selectable)
White balance		auto/manual/one shot (software selectable)
Trigger mode		edge preset trigger (software selectable)	software and hardware trigger (pulse width and edge preset)
Trigger controls		integration end signal, readout signal control, HD trigger trimming control
I/O ports		-	4 programmable input/output ports (2 input ports & 2 output ports available
Inputs and outputs		USB 2.0 high speed
Power voltage		+5V via USB cable
Power current		1.75W, < 350 mA
Dimensions (W x H x D)		51mm x 51mm x 41.6mm dimensional drawing STC-TC33USB-AT  51mm x 51mm x 44.3mm dimensional drawing STC-TC33USB-AS	50mm x 50mm x 40.8mm
Lenses and mounts		CS mount/micro lens mount
Tripod		2 screws on the bottom plate
Connectors		USB standard	mini USB (lock down type available) & USB signal on the 12 pin Hirose
Weight		145g
Operating temperature		0°C to 40°C
Operating humidity		RH: 0 to 85% (no condensation)
Storage temperature		-30°C to 65°C
Storage humidity		RH: 0 to 90% (no condensation)
Vibration		20 Hz to 200 Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard compliancy		TBDEMS: EN61000-6-2, EMI EN61000-6-3 (class B)
		Software
Image viewing software		basic and advanced menus (included)
Measurement software		measurement and calibration software support foot pedal controls (optional)
Supplied drivers		Windows 2000, XP, Vista 32 bit Vista 64 bit, 7 Linux Direct Show Twain National Instruments LabView NvTec (Halcon)
SDK		free SDK (software development kit) supplied on request standard and trigger SDK SDK functions include: 1) Bayer filter color interpolation                      nearest neighbor replication                            bilinear (bilinear interpolation)                       bicubic (cubic convolution) 2) white balance (auto/manual/one shot) 3) electronic shutter control (auto (electronic iris)/manual (fixed shutter) 4) image filling 5 ) others
System requirements		Operating system: Windows 2000 (SP4)/XP (SP2), Vista, Linux, Win 7 32bit/64bit USB port: USB 2.0

 

STC-TC83USB-A/ASH
With software trigger		With software and hardware trigger

USB 2.0 interface. 1/3" progressive scan. XGA resolution. 0.45 o 1.0 gamma (variable software set). Electronic or fixed shutter. AGC On/Off selectable. Compact size. SDK Sentech available. Direct X and driver available. Soft trigger Extended low light capability via trigger software. Hard trigger versions available(STC-TC83USB-ASH) Two versions:  with top connections (STC-TC83USB-AT).  with back connections (STC-TC83USB-AS).
Download USB viewing software for 32x     HERE Download USB viewing software for 64x     HERE USB camera software user's manual  (V 8.0 pdf)
Configurations
AS	AT top view	AT rear view
ASH C mount	ASH CS mount	ASH rear view

		STC-TC83USB-AT STC-TC83USB-AS	STC-TC83USB-ASH
Resolution		XGA
Signal format		progressive scan
Image sensor		1/3" interline transfer CCD (ICX204AQ)
Total pixels		1077 (H) x 768 (V)
Effective pixels		1034 (H) x 779 (V)
Chip size		5.80 (H) x 4.92 (V) mm
Cell size		4.65 (H) x 4.65 (V) μm
Scanning methods		full scanning, 1/1 partial scanning, 1/2 partial scanning, 1/4 partial scanning, variable partial scanning
Horizontal drive frequency		29.5 MHz
Maximum frame rate	full scan	29.18 fps
	1/2 partial scan	60.02 fps
	1/4 partial scan	120.35 fps
Resolution		1024 (H) x 768 (V) at full scan 1024 (H) x 344 (V) at 1/2 partial scan 1024 (H) x 136 (V) at 1/4 partial scan
Minimum illumination		4.24 lux with f=1.2	5.28 lux with f=1.2
Sync system		internal
Electronic shutter		auto (electronic iris)/manual (software selectable)
Gain		auto/manual (software selectable)
Gamma		manual (software selectable)
White balance		auto/manual/one shot (software selectable)
Trigger mode		edge preset trigger (software selectable)	software and hardware trigger (pulse width and edge preset)
Trigger controls		integration end signal, readout signal control, HD trigger trimming control
I/O ports		-	4 programmable input/output ports (2 input ports & 2 output ports available
Inputs and outputs		USB 2.0 high speed
Power voltage		+5V via USB cable
Power current		1.60W,  <350 mA
Dimensions (W x H x D)		51mm x 51mm x 41.6mm dimensional drawing STC-TC83USB-AT  51mm x 51mm x 44.3mm dimensional drawing STC-TC83USB-AS	50mm x 50mm x 40.8mm
Lenses and mounts		CS mount/micro lens mount
Tripod		2 screws on the bottom plate
Connectors		USB standard	mini USB (lock down type available) & USB signal on the 12 pin Hirose
Weight		145g
Operating temperature		0°C to 40°C
Operating humidity		RH: 0 to 85% (no condensation)
Storage temperature		-30°C to 65°C
Storage humidity		RH: 0 to 90% (no condensation)
Vibration		20 Hz to 200 Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard compliancy		TBDEMS: EN61000-6-2, EMI EN61000-6-3 (class B)
		Software
Image viewing software		basic and advanced menus (included)
Measurement software		measurement and calibration software support foot pedal controls (optional)
Supplied drivers		Windows 2000, XP, Vista 32 bit Vista 64 bit, 7 Linux Direct Show Twain National Instruments LabView NvTec (Halcon)
SDK		free SDK (software development kit) supplied on request standard and trigger SDK SDK functions include: 1) Bayer filter color interpolation                      nearest neighbor replication                            bilinear (bilinear interpolation)                       bicubic (cubic convolution) 2) white balance (auto/manual/one shot) 3) electronic shutter control (auto (electronic iris)/manual (fixed shutter) 4) image filling 5 ) others
System requirements		Operating system: Windows 2000 (SP4)/XP (SP2), Vista, Linux, Win 7 32bit/64bit USB port: USB 2.0

 

STC-TC152USB-A/ASH
With software trigger		With software and hardware trigger

USB 2.0 interface. 1/2" progressive scan. SXGA resolution. 0.45 or 1.0 gamma (variable software set). Electronic or fixed shutter. AGC On/Off selectable. Compact size. SDK Sentech available. Direct X and driver available. Soft trigger. Hard trigger versions available(STC-TC152USB-ASH). No IR filter version available. Two versions: with top connections (STC-TC152USB-AT). with back connections (STC-TC152USB-AS).
Download USB viewing software for 32x     HERE Download USB viewing software for 64x     HERE USB camera software user's manual  (V 8.0 pdf)
Configurations
AS	AT top view	AT rear view
ASH C mount	ASH CS mount	ASH rear view

		STC-TC152USB-AT STC-TC152USB-AS	STC-TC152USB-ASH
Resolution		SXGA
Signal format		progressive scan
Image sensor		1/2" interline transfer CCD (ICX205AK)
Total pixels		1434 (H) x 1050 (V)
Effective pixels		1392 (H) x 1040 (V)
Chip size		7.60 (H) x 6.20 (V) mm
Cell size		4.65 (H) x 4.65 (V) μm
Scanning methods		full scanning, 1/1 partial scanning, 1/2 partial scanning, 1/4 partial scanning, variable scanning
Horizontal drive frequency		36.818 MHz
Maximum frame rate	full scan	19.26 fps
	1/2 partial scan	38.52 fps
	1/4 partial scan	77.04 fps
Resolution		1280 (H) x 1024 (V) at full scan 1280 (H) x 476 (V) at 1/2 partial scan 1280 (H) x 184 (V) at 1/4 partial scan
Minimum illumination		2,27 lux with f=1.2
Sync system		internal
Electronic shutter		auto (electronic iris)/manual (software selectable)
Gain		auto/manual (software selectable)
Gamma		manual (software selectable)
White balance		auto/manual/one shot (software selectable)
Trigger mode		edge preset trigger (software selectable)	software and hardware trigger (pulse width and edge preset)
Trigger controls		integration end signal, readout signal control, HD trigger trimming control
I/O ports		-	4 programmable input/output ports (2 input ports & 2 output ports available
Inputs and outputs		USB 2.0 high speed
Power voltage		+5V via USB cable
Power current		2.25W,  < 450 mA
Dimensions  (W x H x D)		51mm x 51mm x 41.6mm dimensional drawing STC-TC152USB-AT  51mm x 51mm x 44.3mm dimensional drawing STC-TC152USB-AS	50mm x 50mm x 40.8mm
Weight		145g
Lenses and mounts		C mount
Tripod		2 screws on the bottom plate
Connectors		USB standard	mini USB (lock down type available) & USB signal on the 12 pin Hirose
Operating temperature		0°C to 40°C
Operating humidity		RH: 0 to 85% (no condensation)
Storage temperature		-30°C to 65°C
Storage humidity		RH: 0 to 90% (no condensation)
Vibration		20 Hz to 200 Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard compliancy		TBDEMS: EN61000-6-2, EMI EN61000-6-3 (class B)
		Software
Image viewing software		basic and advanced menus (included)
Measurement software		measurement and calibration software support foot pedal controls (optional)
Supplied drivers		Windows 2000, XP, Vista 32 bit Vista 64 bit, 7 Linux Direct Show Twain National Instruments LabView NvTec (Halcon)
SDK		free SDK (software development kit) supplied on request standard and trigger SDK SDK functions include: 1) Bayer filter color interpolation                      nearest neighbor replication                            bilinear (bilinear interpolation)                       bicubic (cubic convolution) 2) white balance (auto/manual/one shot) 3) electronic shutter control (auto (electronic iris)/manual (fixed shutter) 4) image filling 5 ) others
System requirements		Operating system: Windows 2000 (SP4)/XP (SP2), Vista, Linux, Win 7 32bit/64bit USB port: USB 2.0

 

STC-TC202USB-A/ASH
With software trigger		With software and hardware trigger

USB 2.0 interface. 1/1.8" progressive scan. UXGA resolution. 0.45 o 1.0 gamma (variable software set). Electronic or fixed shutter. AGC On/Off selectable. Compact size. SDK Sentech available. Direct X and driver available. Soft trigger. Hard trigger versions available(STC-TC202USB-ASH). No IR filter version available. Two versions: with top connections (STC-TC202USB-AT). with back connections (STC-TC202USB-AS).
Download USB viewing software for 32x     HERE Download USB viewing software for 64x     HERE USB camera software user's manual  (V 8.0 pdf)
Configurations
AS	AT top view	AT rear view
ASH C mount	ASH CS mount	ASH rear view

		STC-TC202USB-AT STC-TC202USB-AS	STC-TC202USB-ASH
Resolution		UXGA
Signal format		progressive scan
Image sensor		1/1.8" interline transfer CCD (ICX274AQ)
Total pixels		1688 (H) x 1248 (V)
Effective pixels		1628 (H) x 1236 (V)
Chip size		8.50 (H) x 6.80 (V) mm
Cell size		4.40 (H) x 4.40 (V) μm
Scanning methods		full scanning, 1/1 partial scanning, 1/2 partial scanning, 1/4 partial scanning, variable scanning
Horizontal drive frequency		36.818 MHz
Maximum frame rate	full scan	15.32 fps
	1/2 partial scan	30.63 fps
	1/4 partial scan	61.27 fps
Resolution		1600 (H) x 1200 (V) at full scan 1600 (H) x 544 (V) at 1/2 partial scan 1600 (H) x 208 (V) at 1/4 partial scan
Minimum illumination		1.39 lux with f=1.2
Sync system		internal
Electronic shutter		auto (electronic iris)/manual (software selectable)
Gain		auto/manual (software selectable)
Gamma		manual (software selectable)
White balance		auto/manual/one shot (software selectable)
Trigger mode		edge preset trigger (software selectable)	software and hardware trigger (pulse width and edge preset)
Trigger controls		integration end signal, readout signal control, HD trigger trimming control
I/O ports		-	4 programmable input/output ports (2 input ports & 2 output ports available
Inputs and outputs		USB 2.0 high speed
Power voltage		+5V via USB cable
Power current		2.80W,  <560 mA
Dimensions  (W x H x D)		51mm x 51mm x 41.6mm dimensional drawing STC-TC202USB-AT  51mm x 51mm x 44.3mm dimensional drawing STC-TC202USB-AS	50mm x 50mm x 40.8mm
Weight		145g
Lenses and mounts		C mount
Tripod		2 screws on the bottom plate
Connectors		USB standard	mini USB (lock down type available) & USB signal on the 12 pin Hirose
Operating temperature		0°C to 40°C
Operating humidity		RH: 0 to 85% (no condensation)
Storage temperature		-30°C to 65°C
Storage humidity		RH: 0 to 90% (no condensation)
Vibration		20 Hz to 200 Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude 6ms, 3 directions 3 times each
Standard compliancy		TBDEMS: EN61000-6-2, EMI EN61000-6-3 (class B)
		Software
Image viewing software		basic and advanced menus (included)
Measurement software		measurement and calibration software support foot pedal controls (optional)
Supplied drivers		Windows 2000, XP, Vista 32 bit Vista 64 bit, 7 Linux Direct Show Twain National Instruments LabView NvTec (Halcon)
SDK		free SDK (software development kit) supplied on request standard and trigger SDK SDK functions include: 1) Bayer filter color interpolation                      nearest neighbor replication                            bilinear (bilinear interpolation)                       bicubic (cubic convolution) 2) white balance (auto/manual/one shot) 3) electronic shutter control (auto (electronic iris)/manual (fixed shutter) 4) image filling 5 ) others
System requirements		Operating system: Windows 2000 (SP4)/XP (SP2), Vista, Linux, Win 7 32bit/64bit USB port: USB 2.0

Reference technical notes
Introduction to CCD cameras

Cliccate sulle  parole evidenziate in giallo per vedere collegamenti a figure o ad altre pagine.
Click on words highlighted in yellow to view links.

Cliccate sulle immagini miniaturizzate per vederle ingrandite.
Click on thumbnails to view enlarged images.

Rapitron s.r.l.
NEW ADDRESS/NUOVO INDIRIZZO
  Via S.Antonio Maria Zaccaria 4  -  20122 Milano ITALIA
      Tel.: +39 02 659.82.82   Fax: +39 02 65.45.25

P.IVA/VAT No:  IT 04498890153

Queste pagine sono disegnate e aggiornate da Rapitron s.r.l.
I marchi citati sono di proprietà dei rispettivi proprietari.
Le specifiche dei prodotti sono esposte così come dichiarate dai singoli fabbricanti e sono soggette a cambiamenti senza preavviso.
Sito ospitato da Range s.a.s.- Genova

These pages are designed and updated esclusively by Rapitron s.r.l.
All trademarks are property of the respective owners.
All products specifications are shown as declared by manufacturers and are  subject to change without prior notice.
This Web Site is hosted by Range s.a.s. - Genova

Copyright © 2011 Rapitron s.r.l.
Last modified 23-06-2011