Search

Custom - Monochrome - Color - Line scan - Accessories

Monochrome cameras:
 

Board interlaced - Board progressive scan - USB board
Interlaced - Progressive scan - Camera Link - USB - GigE

All cameras are supplied without lens, unless otherwise indicated

STC-CL33A/CL83A
Lightweight compact progressive scan camera. 1/3" 659(V) x 494(H) VGA o 1034(V) x 779(H) XGA CCD sensor 90 fps or 30fps frame rate Camera Link output. Pulse width and edge pre-select trigger mode.
		STC-CL33A	STC-CL83A
Image sensor		1/3" progressive scan interline transfer CCD ICX424AQ	1/3" progressive scan interline transfer CCD ICX424AL
Total pixels		692 (H) x 504 (V)	1077(H) x 788(V)
Effective pixels		659 (H) x 494 (V)	1034 (H) x 779 (V)
Active pixels		648(H) x 494(V)	1024 (H) x 768 (V)
Chip size		5.79(H) x 4.89(V) mm	5.80(H) x 4.92(V) mm
Cell size		7.4 µm x 7.4 µm (square cell)	4.65 µm x 4.65 µm (square cell)
Scanning method		full scanning, partial full scanning, ½ partial scanning, ¼ partial scanning variable partial scanning, binning, binning ½ partial scanning, binning ¼ partial scanning, binning variable partial scanning
Vertical frequency (frame rate)		31.47 Hz (30 fps) 62.94 Hz (60 fps) 94.784 Hz (90 fps)	29.2 Hz
Horizontal frequency		15.7343 kHz (30 fps) 31.4685 kHz (60 fps) 47.2028 kHz (90 fps)	23.23 KHz
Pixel frequency		12.2727 MHz (30 fps) 24.5454 MHz (60 fps) 36.8181 MHz (90 fps)	29.5 MHz
S/N ratio		8 bit output: <=3 digit (gain 0 dB) 10 bit output: <= 10 digit (gain 0 dB)
Minimum illumination		0.12 lux at f1.2	0.14 lux at f1.2
Sync system		internal/external
Video output		digital: 8 or 10 bit Camera Link
Tap		1 tap
Shutter speed		OFF, 1/3 to 1/40000 sec (variable at every H and clock) (30 fps) OFF, 1/7 to 1/80000 sec (variable at every H and clock) (60 fps) OFF, 1/11 to 1/120000 sec ((variable at every H and clock) (90 fps)	OFF, 1/5~1/96000 sec (variable 1H step)
Gain		0 to 27 dB
Gamma		1.0
Power supply		12Vdc ± 10%
Power consumption		>1.8W
Trigger mode		edge preset trigger: V reset, non-reset  pulse width trigger: V reset, non-reset
Communication		RS-232 via Camera Link connector
Dimensions (H x W x D)		28mm x 28mm x 29.5mm (not including lens mount and the connector) 28mm x 28mm x 40mm (not including the connector) dimensional drawing
Optical filter		No IR cut filter
Optical center accuracy		positional accuracy in H and V directions: ± 0.31mm rotational accuracy of hand V: ± 2.1°
Material	case	front, base and rear: aluminum die cast (ADC12) cover: steel sheet covered with zinc
	tripod	polycarbonate ABS
Lens mount		C mount
Interface connector		HR10A-7R-6PB (Hirose) or equivalent
Tripod		tripod can be attached to 4 plates (4 screws on the bottom plate, 3 screws on the other 3 plates)
Weight		approx 52g (camera 43g, tripod 9g)
Operation temperature		-5C° to 50C° relative humidity: 0 to 85% (no condensation)
Storage temperature		-30C° to 65C° relative humidity: 0 to 90% (no condensation)
Vibration		20 to 200Hz at 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude  6ms, 3 directions 3 times each
Standard compliancy		EMS: EN610000-6-2, EMI: EN55011 (class B)
RoHS		RoHS compliant
Rear panel

 

STC-CL152A
Lightweight compact progressive scan camera. 1/2" 1360(V) x 1040(H) SXGA CCD sensor 19 fps frame rate Camera Link output. Pulse width and edge pre-select trigger mode.
Image sensor		1/2" progressive scan interline transfer CCD ICX205AL
Total pixels		1434 (H) x 1050 (V)
Effective pixels		1392 (H) x 1040 (V)
Active pixels		1360(H) x 1040(V)
Chip size		7.6(H) x 6.2(V) mm
Cell size		4.65 µm x 4.65 µm (square cell)
Scanning method		full scanning, partial full scanning, ½ partial scanning, ¼ partial scanning variable partial scanning, binning, binning ½ partial scanning, binning ¼ partial scanning, binning variable partial scanning
Vertical frequency (frame rate)		15.28 Hz (15 fps) 19.3 Hz (19 fps)
Horizontal frequency		15.998 kHz (15 fps) 20.57 kHz (19 fps)
Pixel frequency		28.6363 MHz (15 fps) 36.8181 MHz (19 fps)
S/N ratio		8 bit output: <=3 digit (gain 0 dB) 10 bit output: <= 10 digit (gain 0 dB)
Minimum illumination		0.12 lux at f1.2
Sync system		internal/external
Video output		digital: 8 or 10 bit Camera Link
Tap		1 tap
Shutter speed		OFF, 1/3 to 1/93000 sec (variable at every H and clock) (15 fps) OFF, 1/5 to 1/20000 sec (variable at every H and clock) (19 fps)
Gain		0 to 27 dB
Gamma		1.0
Power supply		12Vdc ± 10%
Power consumption		>2.5W
Trigger mode		edge preset trigger: V reset, non-reset  pulse width trigger: V reset, non-reset
Communication		RS-232 via Camera Link connector
Dimensions (H x W x D)		28mm x 28mm x 29.5mm (not including lens mount and the connector) 28mm x 28mm x 40mm (not including the connector) dimensional drawing
Optical filter		No IR cut filter
Optical center accuracy		positional accuracy in H and V directions: ± 0.31mm rotational accuracy of hand V: ± 2.1°
Material	case	front, base and rear: aluminum die cast (ADC12) cover: steel sheet covered with zinc
	tripod	polycarbonate ABS
Lens mount		C mount
Interface connector		HR10A-7R-6PB (Hirose) or equivalent
Tripod		tripod can be attached to 4 plates (4 screws on the bottom plate, 3 screws on the other 3 plates)
Weight		approx 52g (camera 43g, tripod 9g)
Operation temperature		-5C° to 45C° relative humidity: 0 to 85% (no condensation)
Storage temperature		-30C° to 65C° relative humidity: 0 to 90% (no condensation)
Vibration		20 to 200Hz at 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude  6ms, 3 directions 3 times each
Standard compliancy		EMS: EN610000-6-2, EMI: EN55011 (class B)
RoHS		RoHS compliant
Rear panel

 

STC-CL202A/CL232A
STC-CL202A	STC-CL232A
Lightweight compact progressive scan camera. 1/1.8" 1620(V) x 1220(H) UXGA CCD sensor. 30 or 15fps frame rate Camera Link output. Pulse width and edge pre-select trigger mode.

		STC-CL202A	STC-CL232A
Image sensor		1/1.8" progressive scan interline transfer CCD ICX274AL
Total pixels		1688 (H) x 1248 (V)
Effective pixels		1628 (H) x 1236 (V)
Active pixels		UXGA: 1620 (H) x 1220 (V)
Chip size		8.5(H) x 6.8(V) mm
Cell size		4.4 µm x 4.4 µm (square cell)
Scanning method		full scanning, partial full scanning, ½ partial scanning, ¼ partial scanning variable partial scanning, binning, binning ½ partial scanning, binning ¼ partial scanning, binning variable partial scanning
Vertical frequency (frame rate)		15.3164 Hz	30.854 Hz
Horizontal frequency		19.176 kHz	38.352 KHz
Pixel frequency		36.8181 MHz	73.636 MHz
S/N ratio		8 bit output: <= 3 digit (gain 0 dB) 10 bit output: <= 10 digit (gain 0 dB)	8 bit output: <= 4 digit (gain 0 dB) 10 bit output: <= 15 digit (gain 0 dB)
Minimum illumination		0.06 lux at f1.2	0.07 lux at f1.2
Sync system		internal/external
Video output		digital: 8 or 10 bit Camera Link (base configuration)
Tap		1 tap	2 tap
Shutter speed		OFF, 1/4 to 1/120000 sec (variable at every H and clock)	OFF, 1/9 to 1/240000 sec (variable at every H and clock)
Gain		0 to 25 dB
Gamma		1.0
Power supply		12Vdc ± 10%
Power consumption		>4.0W
Trigger mode		edge preset trigger: V reset, non-reset  pulse width trigger: V reset, non-reset
Communication		RS-232 via Camera Link connector
Dimensions (H x W x D)		28mm x 28mm x 29.5mm (not including lens mount and the connector) 28mm x 28mm x 40mm (not including the connector) dimensional drawing	28mm x 28mm x 36.5mm (not including lens mount and the connector) 28mm x 28mm x 47mm (not including the connector) dimensional drawing
Optical filter		No IR cut filter
Optical center accuracy		positional accuracy in H and V directions: ± 0.31mm rotational accuracy of hand V: ± 2.1°
Material	case	front, base and rear: aluminum die cast (ADC12) cover: steel sheet covered with zinc
	tripod	polycarbonate ABS
Lens mount		C mount
Interface connector		HR10A-7R-6PB (Hirose) or equivalent
Tripod		tripod can be attached to 4 plates (4 screws on the bottom plate, 3 screws on the other 3 plates)
Weight		approx 52g (camera 43g, tripod 9g)
Operation temperature		-5C° to 45C° relative humidity: 0 to 85% (no condensation)
Storage temperature		-30C° to 65C° relative humidity: 0 to 90% (no condensation)
Vibration		20 to 200Hz at 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock		acceleration 70G, half amplitude  6ms, 3 directions 3 times each
Standard compliancy		EMS: EN610000-6-2, EMI: EN55011 (class B)
RoHS		RoHS compliant
Rear panel

 

STC-CL500A
Lightweight compact progressive scan camera. 2/3" 2448(H) x 2058(V) CCD sensor 16 fps frame rate Camera Link output. Pulse width and edge pre-select trigger mode.
Image sensor	2/3" progressive scan interline transfer CCD ICX625AL
Total pixels	2456 (H) x 2058 (V)
Active pixels	2448 (H) x 2058 (V)
Chip size	9.93(H) x 8.70(V) mm
Cell size	3.45 µm x 3.45 µm (square cell)
Scanning method	full scanning, partial full scanning, ½ partial scanning, ¼ partial scanning variable partial scanning, binning, binning ½ partial scanning, binning ¼ partial scanning, binning variable partial scanning
Vertical frequency (frame rate)	16 Hz
Horizontal frequency	33.264 kHz
Pixel frequency	64 MHz
S/N ratio	8 bit output: <=4 digit (gain 0 dB) 10 bit output: <= 15 digit (gain 0 dB) 12 bit output: <= 60 digit (gain 0 dB)
Minimum illumination	0.24 lux at f1.2
Sync system	internal
Video output	digital: 8,10 or 12 bit Camera Link
Tap	2 taps
Shutter speed	OFF, 1/8 to 1/209000 sec (variable at every H and clock)
Gain	0 to 18.309 dB
Gamma	1.0
Power supply	12Vdc ± 10%
Power consumption	>4.0W
Trigger mode	edge preset trigger: V reset, non-reset  pulse width trigger: V reset, non-reset
Communication	RS-232 via Camera Link connector
Dimensions (H x W x D)	35mm x 35mm x 30.2mm (not including lens mount and the connector) 35mm x 35mm x 40.7mm (not including the connector) dimensional drawing
Optical filter	No IR cut filter
Material	aluminum
Lens mount	C mount
Interface connector	HR10A-7R-6PB (Hirose) or equivalent
Weight	approx 80g
Operation temperature	-5C° to 40C° relative humidity: 0 to 85% (no condensation)
Storage temperature	-30C° to 65C° relative humidity: 0 to 90% (no condensation)
Vibration	20 to 200Hz at 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min each
Shock	acceleration 38G, half amplitude  6ms, 3 directions 3 times each
Standard compliancy	EMS: EN610000-6-2, EMI: EN55011 (class B)
RoHS	RoHS compliant
Rear panel

 

STC-CL1500    discontinued
Progressive scan camera with digital Camera Link and analog output. 1360 x 1024 1/2" CCD. Square pixels. Double speed & standard speed. Three scanning modes: normal, partial, & draft. Internal or external sync (Hd/Vd). Pulse width & edge pre-select trigger modes.
Image sensor	progressive scan 1/2" CCD (ICX205AL sensor)
Effective No.of pixels	1392 (H) x 1040 (V)
Active No.of pixels	1360 (H) x 1024 (V)
Chip size	7.60 (H) x 6.20 (V) mm
Cell size	4.65 µm x 4.65 µm (square cell)
Scanning size	6.47 (H) x 4.84 (V) mm
H drive frequency	double speed: 28.636 kHz normal speed: 14.318 kHz
H frequency	double speed: 15.997 kHz normal speed: 7.999 kHz
Frequenza verticale	double speed: 14.95 Hz normal speed: 7.49 Hz
Lens mount	C
Sync system	internal or external switchable, auto switching
External sync signal	Hd/Vd 3-5Vpp, 75Ω (with On/Off switch)
Internal sync signal	Hd/Vd outputs 2-5Vp-p, 75Ω (with On/Off switch)
Video output	Analog: 1 Vp-p a 75Ω. Simultaneous double output Digital: 10 bit Camera Link (Base configuration). Simultaneous double output
S/N ratio	56 dB min(AGC Off)
Gamma	1.0
Shutter trigger	pulse width trigger((3-1/10.000 sec) and edge pre select trigger(10 steps)
Electronic shutter	normal speed (10 steps) up to 1/5000 double speed (10 steps) up to 1/10000 shutter switch configuration
Gain	AGC/Fisso/Manuale gain  switch configuration
Minimum illumination	3.0 lux at f1.2 with max gain
CameraLink connector	Camera Link connector configuration
12 pins connector	12 pin connector configuration
Dip switch	dip-switch configuration
Power supply	12Vdc
Operating temperature	-10C° to 45C°
Storage temperature	-30° to 60°C
Dimensions (W x H x D)	44mm x 29mm x 90mm dimensional drawing
Rear panel

 

Reference technical notes
Introduction to CCD cameras  Progressive scan cameras

Cliccate sulle  parole evidenziate in giallo per vedere collegamenti a figure o ad altre pagine.
Click on words highlighted in yellow to view links.

Cliccate sulle immagini miniaturizzate per vederle ingrandite.
Click on thumbnails to view enlarged images.

Rapitron s.r.l.
NEW ADDRESS/NUOVO INDIRIZZO
  Via S.Antonio Maria Zaccaria 4  -  20122 Milano ITALIA
      Tel.: +39 02 659.82.82   Fax: +39 02 65.45.25

P.IVA/VAT No:  IT 04498890153

Queste pagine sono disegnate e aggiornate da Rapitron s.r.l.
I marchi citati sono di proprietà dei rispettivi proprietari.
Le specifiche dei prodotti sono esposte così come dichiarate dai singoli fabbricanti e sono soggette a cambiamenti senza preavviso.
Sito ospitato da Range s.a.s.- Genova

These pages are designed and updated esclusively by Rapitron s.r.l.
All trademarks are property of the respective owners.
All products specifications are shown as declared by manufacturers and are  subject to change without prior notice.
This Web Site is hosted by Range s.a.s. - Genova

Copyright ©1998 - 2011 Rapitron s.r.l.
Last modified 21-01-2011